reacciones quimicas – Reacciones Quimicas

Lorem

Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.

LOCATE US!

Plants and General Offices
Carretera Saltillo Km. 7
Santa Catarina, N.L. 66359
(81) 81510200
Guadalajara branch
Calle #1 3568 Col. La Nogalera
Guadalajara, Jalisco 44470
(33) 3666 0705 y 3666 0931
México branch
Cerrada de Tecojotes s/n Lote 4 Bodega 1
Fraccionamiento Industrial San Martín Obispo
Cuatitlán Izcalli, Edo. De México 54769
(55) 5819 9064 y 5819 9068

Reacciones Químicas. S.A. de C.V. It has international certifications such as ISO 9001: 2015, ISO 14001: 2015, Integral Responsibility, and OHSAS 18001, which leads it to be at the forefront in the areas corresponding to Quality, Safety, Health and Environmental Protection.

SITE MAP

CONTACT US

We will answer your request shortly

AL – 21245HV	Good tolerance to naphtha gas, good drying time, shine and hardness. It has good durability, good compatibility with other medium resins. Domestic and primary enamels. General purpose coatings with good gloss and good leveling by brush and / or gun.
AL – 21250HV	High viscosity, good tolerance to naphtha gas. Good compatibility with other medium resins and with some long resins. Manufacture of domestic enamels, industrial primaries.
AL21250HVB	Good gloss, high viscosity, air drying, compatibility with long and medium resins. Good compatibility with solvents such as Xylol, Toluol and MIBK. Domestic, primary, enamel enamels, brush and gun finishes. Coatings for general use.
AL – 212 – 50T	Good air drying properties. Compatible with chlorinated rubber. Strength and durability. Manufacture of traffic paints., Domestic enamel and general purpose primary applied by brush and / or gun.
AL – 212 – 50X	Excellent air drying properties, very good durability and resistance to yellowing. Compatible with red rubber. It is recommended for domestic, primary and industrial primary enamels and for the manufacture of traffic paints in combination with chlorinated rubber.
AL – 212 – 70X	Excellent air drying properties. It is excellent for the formulation of enamels with low VOC values.
AL – 212 – 501	Excellent air drying properties, gloss and hardness. Excellent for the manufacture of domestic and primary enamels. Applications with brush or gun.
AL212501TS	Excellent compatibility with chlorinated rubber, very good air-dried and very good adhesion. Due to its compatibility with chlorinated rubber, it is used in the manufacture of traffic paints.
AL – 212 – 504	Excellent air drying properties. It is applied in household enamels, primary.
AL – 223 – 50	Good durability and resistance to yellowing. Good air drying properties, brightness hardness. For the manufacture of enamels, primary, and domestic varnishes. General use coatings with good gloss and leveling, in bricha applications or with gun.

AL – 222 – 60	Good shine, brochabilidad, hardness. Resistance to yellowing, good drying and good compatibility with long resins. Manufacture of enamels, primary and domestic varnishes for low VOC¨s.
AL – 310 – 00	Excellent wetting properties, good air drying. 100% solid. Latex modifier. Used in grinding pigments for inks.
AL – 312 – 60	Excellent wetting properties. Magnificent properties of gloss brochabilidad and durability. Very good resistance to weathering and rubbing. High gloss and semi-gloss architectural glazes, exterior paints, magnificent grinding media for excellent quality coatings, enamels and varnishes applied by brush, exterior varnishes for wood.
AL – 313 – 60	Good drying and hardness development. Good shine and brochabilidad. Excellent for decorative enamels, primary and grinding vehicles.
AL – 315 – 00	Excellent pigment wetting properties for grinding and offset bases. In the grinding of pigments for inks, domestic enamels.
AL – 330 – 70	Excellent wetting properties. Magnificent properties of brightness, brochabilidad and durability. High solids and low viscosity, very good weather and rub resistance. It is widely recommended as a grinding medium for air drying coatings. High gloss and semi-gloss architectural glazes applied by brush or gun.

AL – 530150X	Quick air drying. Excellent color and gloss retention. Good resistance to gasoline and durability in any weather. Compatible with acrylic resins. Quick-drying enamels, automotive repainting in combination with acrylic resins. It is recommended to use a maximum of 30% acrylic resin to prevent the film from becoming very brittle.
AL – 530160X	Quick air drying. Excellent color, hardness development and gloss retention, good gasoline resistance and durability in any weather. Resistance to the saline chamber. This resin is the same as Al-5301-50X. Quick-drying enamels, automotive repainting in combination with acrylic resins. It is recommended to use a maximum of 30% acrylic resin to avoid brittle films.
AL – 530370X	Quick drying, good shine and leveling. Formulation of finishes and funds for wood. In two component finishes with isocyanates.
AL – 530460X	Quick touch drying and hardness development, very good compatibility with acrylic resins. High gloss, flexible and excellent adhesion to metal. Good resistance to yellowing and weathering. Enamels for automotive repainting, fast drying and low-baking industrial enamels. Finishes of two components catalyzed with isocyanates.
AL5315 – 60X	Two-component coatings for Wood – Finishes Coatings for Automotive Repainting – Finishes in combination with acrylic resin (70/30)
AL5316 – 60X	Two-component coatings for Wood – Finishes and Funds

AL – 120 – 60X	Economic resin for ovens in general. It is recommended also for air drying, compatible with vinyl.
AL – 140 – 60T	Excellent color and gloss properties. It has a wide range of baking, when making mixtures with ureas gives very good compatibility, hardness, adhesion and flexibility. It is equal to 140-60X, but diluted in toluene. It works as a plasticizer in NITROCELLULOSE lacquers. It is used in white baking enamels.
AL – 140 – 60X	Excellent color, gloss and resistance properties yellowing It has a wide baking range, when doing mixtures with ureas gives very good compatibility, hardness, adhesion and flexibility.
AL – 142 – 60X	Excellent color and billo properties. It has a wide range of baking, making mixtures with ureas gives us very good compatibility, hardness, adhesion and flexibility. It works as a plasticizer in NITROCELLULOSE lacquers. It is used for white baking enamels.
AL – 180 – 60X	Excellent cure at low temperatures (80 ° C). Excellent plasticizer for nitrocellulose lacquers. Baking enamels
AL5309 – 60X	For automotive repainting, household, industrial enamels and general purpose coatings. Good gloss, drying, color retention.
AL5312 – 60X	For automotive repainting, household, industrial enamels and general purpose coatings. Good gloss, drying, color retention.
AL7390 – 60X	It is designed for the formulation of varnishes and polyurethane lacquers. It has high brightness, good strength and hardness.
AL1130860X	This resin is the same as AL-11308-60T, but dissolved in xylene. It is drying a little slower than the AL-11308-60T. It is excellent in wood finishes with good gloss. It is compatible with nitrocellulose. It is widely recommended in wood finishes. for its compatibility with nitrocellulose. It is used in two component systems.
AV – 926 – X60	It has good properties in baked enamels, with nitrocellulose lacquers it presents very short drying times which allows it to handle the applied parts quickly.On the bottoms and lacquers of two components are characterized by their rapid stacking and sanding. It can be applied in: Nitrocellulosic varnishes and lacquers with a high percentage of alkyd resin, putties, coverings and quick-drying and easy sanding primers, two-component polyurethane varnishes and lacquers, general-purpose baked enamels.

810 – 0091R	It can be used in enamels and primers of air drying or baking. In enamels of reticular baking with melamine HMMM obtaining good hardnesses. In air-dried enamels, activate drying with water soluble drying agents.
810 – 0097R	Good stability, good gloss in air and baking finishes, excellent hardness in baking finishes. It can be used in primaries and enamels, air dried or baked. In baking enamels, HMMM melamine is used to crosslink and obtain high hardnesses.

Lorem

CONTACT US

Corporate policy

Política integral

300 – B – 003	High performance white gel coat, formulated for sanitary use. It is low VOC; It has resistance to runoff, porosity and tearing. It has good reparability.
300 – S – 001	High performance bone coat gel, formulated for sanitary use. It is low VOC; It has resistance to runoff, porosity, tearing and pigment separation. It has good reparability.
300 – T – 020	High quality transparent gel coat; specially developed for applications in synthetic marble and solid surface. Meets the requirements specified in ANSI Z124.3; It provides a final finish with very good resistance to water and weathering; It has good retention of brightness and resilience.

100 – B – 015	White gel coat of good quality in its type; Provides a final finish with good gloss retention, weathering and resilience. This gel coat is ready to use, has ease of application, resistance to runoff and curing Quick.
100 – BA – 001	White gel coat of good quality; It provides a final finish with very good water resistance, good gloss retention, weathering and resilience. This gel coat is ready to use, has ease of application, resistance to runoff and fast curing.
100 – GA – 001	Gray gel coat of medium quality; It provides a final finish with very good water resistance, good gloss retention, weathering and resilience. This gel coat is ready to use, has ease of application, resistance to runoff and fast curing.
100 – NA – 001	Medium quality black gel coat; It provides a final finish with very good water resistance, good gloss retention, weathering and resilience. This gel coat is ready to use, has ease of application, resistance to runoff and fast curing.
100 – XB – 002	Neutral gel coat of medium quality. It provides a final finish with very good water resistance, good gloss retention, weathering and resilience. It has ease of application, resistance to runoff and fast curing. Ready-to-use product, requiring only that the appropriate amount of the appropriate catalyst be added.

050 – B001	White coat gel of medium quality in its type; It comes ready to use, has ease of application, resistance to runoff and quick cure.
050 – B – 021	Economic white coat gel. It comes ready to use, has ease of application, resistance to runoff and fast curing.

200-B-113	Isophthalic, white, formulated for the synthetic marble industry where excellent performance and very good stiffness are required, they are finished, pre-accelerated and very good resistance to runoff. Rapid demoulding cycles. Appropriate balance of Viscosity-Thixotropy. Meets the requirements specified in ANSI Z124.1, .2-1995, Secc. 6.1.1. Its use with spray equipment is recommended for the manufacture of sinks and plates in series (automated) processes and in the manufacture of bath tubs.
200-BD-040	Isophthalic, white, formulated for the synthetic marble industry where excellent performance and very good stiffness are required, they are finished, pre-accelerated and very good resistance to runoff. Rapid demoulding cycles. Appropriate balance of Viscosity-Thixotropy. Meets the requirements specified in ANSI Z124.1, .2-1995, Secc. 6.1.1. Its use with spray equipment is recommended for the manufacture of sinks and plates in series (automated) processes and in the manufacture of bath tubs.
200-S-050	Isophthalic, beige, formulated for the synthetic marble industry where excellent performance and very good rigidity are required, they are finished, pre-accelerated and very good resistance to runoff. Rapid demoulding cycles. Appropriate balance of Viscosity-Thixotropy. Meets the requirements specified in ANSI Z124.1, .2-1995, Secc. 6.1.1. Its use with spray equipment is recommended for the manufacture of sinks and plates in series (automated) processes and in the manufacture of bath tubs.
200-XD-001	Isophthalic, neutral ready to pigment, formulated for the synthetic marble industry where excellent performance and very good rigidity are required, they are finished, pre-accelerated and very good resistance to runoff. Rapid demoulding cycles. Appropriate balance of Viscosity-Thixotropy. Its use with spray equipment is recommended for the manufacture of sinks and plates in series (automated) processes and in the manufacture of bath tubs.
300-T-800	ISO-NPG, formulated for the synthetic marble industry where good performance and very good rigidity is required, are finished, pre-accelerated and good UV resistance. Good resistance to yellowing in “Box yellowing” box. Rapid demoulding cycles. The color is controlled by electronic instrumentation. They meet the requirements specified in ANSI Z124.1, .2-1995, Secc. 6.1.1. They are specially designed for use with spray equipment for the manufacture of sinks and plates in series (automated) processes and in the manufacture of bath tubs.
300-T-8100	ISO-NPG, transparent, formulated for the synthetic marble industry where high performance and very good rigidity is required, are finished, pre-accelerated and very good resistance to UV rays. Reduction of yellowing in “Box yellowing” box. Rapid demoulding cycles. The color is controlled by electronic instrumentation. They meet the requirements specified in ANSI Z124.1, .2-1995, Secc. 6.1.1. They are specially designed for use with spray equipment for the manufacture of sinks and plates in series (automated) processes and in the manufacture of bath tubs.
100-B-015	Orthophthalic, white color, formulated for the synthetic marble industry where good performance and good rigidity is required, it is finished, pre-accelerated and with very good resistance to runoff. Rapid demoulding cycles. Appropriate balance of Viscosity-Thixotropy. Good hardness development. Meets the requirements specified in ANSI Z124.1, .2-1995, Secc. 6.1.1. Suo with spray equipment is recommended for the manufacture of sinks and plates in series (automated) processes and in the manufacture of bath tubs.
200-B-118	Isophthalic, white, formulated for the synthetic marble industry where excellent performance and very good stiffness are required, they are finished, pre-accelerated and very good resistance to runoff. Rapid demoulding cycles. Appropriate balance of Viscosity-Thixotropy. Meets the requirements specified in ANSI Z124.1, .2-1995, Secc. 6.1.1. Its use with spray equipment is recommended for the manufacture of sinks and plates in series (automated) processes and in the manufacture of bath tubs.
200-B-120	Isophthalic, white, formulated for the synthetic marble industry where excellent performance and very good stiffness are required, they are finished, pre-accelerated and very good resistance to runoff. Rapid demoulding cycles. Appropriate balance of Viscosity-Thixotropy. Its use with spray equipment is recommended for the manufacture of sinks and plates in series (automated) processes and in the manufacture of bath tubs.